Turboair SOFIA H6 IX/A/60 User's Guide download pdf (Page 19)

Attention! If the hood is not supplied with carbon filter,

then it must be ordered and mounted.

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

(not supplied).

The connecting instructions are supplied with the peripheral

suction unit.

Installation

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the

range hood must be not less than 50cm from electric cookers

and 65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating

indicated on the plate situated inside the hood. If provided with

a plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area, after

installation. If it not fitted with a plug (direct mains connection)

or if the plug is not located in an accessible area, after

installation, apply a double pole switch in accordance with

standards which assures the complete disconnection of the

mains under conditions relating to over-current category III, in

accordance with installation instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

Mounting

The hood is supplied in two versions: model for installation to

the wall and model for installation to the ceiling.

Before beginning installation:

• Check that the product purchased is of a suitable size for

the chosen installation area.

• Remove the charcoal (*) filter/s if supplied (see also

relative paragraph). This/these is/are to be mounted only

if you want lo use the hood in the filtering version.

• Check (for transport reasons) that there is no other

supplied material inside the hood (e.g. packets with

screws (*), guarantees (*), etc.), eventually removing

them and keeping them.

• If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall/ceiling. Otherwise put a thick, protective

covering over countertop, cooktop or range to protect

from damage and debris. Select a flat surface for

assembling the unit. Cover that surface with a protective

covering and place all canopy hood parts and hardware

in it.

• In addition check whether near the installation area of the

hood (in the area accessible also with the hood mounted)

an electric socket is available and it is possible to

connect a fumes discharge device to the outside (only

suction version).

• Carry out all the masonry work necessary (e.g.

installation of an electric socket and/or a hole for the

passage of the discharge tube).

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Installation ceiling model (Island)

Fig. 5-6-7

1. Adjust the extension of the support structure of the hood.

The final height of the hood depends on this adjustment.

Note: In some cases the upper section of the trellis is

fixed to the lower section with 1 or more screws. Check

and remove them temporarily to allow the adjustment of

the support structure.

2. Fix the two sections with a total of 16 screws (4 per

corner).

Apply 1 or 2 brackets as reinforcement for extensions

greater than the minimum (on the basis of what is

envisaged as equipment).

Note: 1 bracket can already be fixed to the trellis

temporarily with 2 screws during transport. Move it into

the desired position or complete fixing it with 6 additional

screws, as follows:

a. Slightly stretch the brackets to be fixed in order to be

able to apply them outside the structure.

b. Position the reinforcement bracket immediately above

the fixing point of the two sections of the structure and fix

with a total of 8 screws (2 per corner).

Fix the second reinforcement bracket, if supplied, in a

position midway between the first reinforcement bracket

and the upper side of the trellis and fix with 8 screws (2

per corner).

Note: check that there is no obstacle to an easy fixing of

the discharge tube (aspiration version) or the deflector

(filtering version) in positioning the reinforcement

bracket(s).

3. Hook the hood to the trellis and make sure that it is

perfectly hooked up. Screw the 16 screws up (4 per

corner) tightly to hook the hood to the trellis.

4. Apply the perforation diagram of the cooking top to the

ceiling vertically (the centre of the diagram must

correspond to the centre of the cooking top and the sides

must be parallel to the sides of the cooking top – the side

of the diagram with the word FRONT corresponds to the

control panel side). Prepare the electrical connection.

5. Make holes as indicated (6 holes for 6 wall dowels – 4

dowels for hooking), and screw 4 screws into the external

holes, leaving a space of about 1 cm between the head

of the screws and the ceiling.

6. Hook the trellis to the ceiling with 4 screws, see operation

4).

7. Screw the 4 screws up tightly.

8. Introduce and screw another 2 screws tightly into the

holes for fixing the safety elements remaining free.

9. Introduce a discharge tube inside the trellis and connect to

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 107 108

Comments to this Manuals

No comments

Turboair SOFIA H6 IX/A/60 User's Guide Page 19

Comments to this Manuals

Related products and manuals for Cooker hoods Turboair SOFIA H6 IX/A/60